Welding…Looks easy doesn’t it?

Today a couple of other things have been crossed off the Job list. 

The new fuse box that the previous owner had installed has had to fit within the tool box/rear inner fender however the edge of this pushes against the connectors, popping them off of the terminals at times.  So I have got the Dremel out and removed a wide chunk of the box so the connectors don’t foul the box.

The other job was to fit the oil breather system.  Again the previous owner made his own box up to do this job which I had previously cleaned up and painted.  So I have used some new rubber tubing and stainless Jubilee Clips and managed to connect it all up.  There were two tubes from the valve covers, one return to the sump and one that vents to the atmosphere.

     

     

Clearly there is still some tidying up of wires…like finding where they go for starters!  The GEL battery I have is nice and slim so will still be sited correctly.  Pleased with getting this done both my dad and I decided to have a crack at welding as we have been lent a welder for the purposes of securing the bolts to the seat pan before it gets upholstered. 

    

These two are my first ever efforts at welding…what a mess!!!  Melted the bolt head quite nicely though! 

   

The molten mess on the right hand bolt is my father’s first attempt at welding….hmmm!

   

Pretty sure we will get some kind of professional to do this as it really is harder than it looks!

The next instalment is likely to be some more wiring…perhaps wiring the starter button in preparation of starting this Goose up sometime in the next few weeks.

New Winkers, A Seat Pan and A GOAT!

The seat pan has now been cut from 3mm stainless steel sheet, holes drilled and powder-coated from the flimsy cardboard template I provided.  And what a good job my helpful friend has done…thanks Lee!  When I first saw the seat pan it reminded me of smoked glass coffee tables from the 1980’s!!

For some reason the special bolt welding machine couldn’t get on with this bit of steel.  I will either use the marine grade M8 bolts that I have and to secure them I will either use a half nut directly under the pan (as the bolt will not be accessible once the seat is upholstered) or get the head of the bolt welded.  It won’t be seen as it will be covered in foam and a lovely tan coloured Tuck n’ Rolled seat.

In the previous blog I mentioned how the number plate was going to partially obscure the indicators so got a 3 line number plate made up to get around that problem.  However, the thread of the indicators was unnecessarily long when compared to the stem so I bit the bullet and got some new indicators with a longer stem/shorter thread.  Now the thread does not intrude into an area where the tyre could enter and I am happy enough with the distance between them with regards to safety…the have LED’s in them.

  

I also have got the rear light bracket/number plate mount back which is powder-coated but think my measuring skills with regards the positioning of holes were on holiday as can be seen by the jaunty angle!  This was mostly rectified by reaming out one of the holes and making it slightly elongated…this helped!  It looks worse than it is due to the fact that it was not tightened up.

Double sided tape helped me mock the plate up.  Due to the extra width of the winkers I have decided that a standard sized 2 line number plate will be used as it will also help clear the rear tyre.  I shall keep the 3 liner for posterity!

A slight change in angle will help with clearance.  Being only 3mm sheet I should be able to bend it up a little to follow the angle of the tyre…but as a dry run it looks alright.

…and with an 8 year old boy aboard!

Oh…and here’s the GOAT!  An award for the “Best Renovation 2014” on the GB Bikers Forum.  Really nice to get some recognition for this steep learning curve I have been on for the past eighteen months.

Cardboard Fabrication!

Well the last session I have had with the little Goose was to find some solution to the number plate, rear light and seat conundrum.  After much rumination, expert judgement and a lot of guesswork a solution was found!  Hurrah! 

The problems were what kind of seat could I have without making too many compromises that would allow me to have the number plate in the right position.  However, a standard sized UK number plate’s width would foul the rear indicators.  Additionally, the rear light with integral number plate holder I had bought was not going to be part of the solution.  So that was £25 not very well spent.  The problem was that what I had purchased was probably meant to be sunk into the rear of a seat or ‘Frenched’ into bodywork somehow as the rear terminals weren’t encased in an aesthetic manner which you should be able to make out in the next photo with the old seat pan.

Although the old seat pan looks okay it doesn’t suit a slim seat in a flat tracker/Brat style plus the rear lights wouldn’t look right because of the issue stated above.  So the old seat pan went back on the shelf.

Out came the cardboard in the shape of a fish tank box!….and some rough lines drawn upon it following the lines of the frame.

Ah!  This was now looking better for the progress of the seat.  So much so that I had splashed out on another rear light, but this time it was in its own casing and would mount on a mudguard or bracket in some way.  As I referred to earlier, the standard UK number plate mounted at the right height/angle so as not to foul the rear wheel, would partially obscure the indicators by about 5mm each side.  I could mount it a little further down a yet to be made home built bracket but the angle would be more horizontal than vertical as per the MOT tester’s handbook.

Having seen regulations that state that motorcycles registered before Jan 1 2001 were eligible for 3 line number plates that’s what I decided to go for.  There is still a bit of a grey area associated with this which I won’t bore you with….so the solution was a flat seat, new bracket for a new rear light to mount to and a slimmer number plate…

             

Thankfully the kind neighbour that sorted the petrol tank out has offered to fabricate the seat pan and number plate bracket and powder coat them both….for nothing again.  This kind of support and expert help is invaluable. 

I have revisited my job list and the next job will be fit the clutch cable before routing it gets too difficult and fit the oil breather tank in place and cut all the hoses to the right length and fit.  Sounds easier than it will probably turn out to be, but hey…at least it ain’t wiring!!!!